有一块SSD，手贱想玩玩开卡，结果就给开废了，下面是log，求各位大神指教
Overall Summary:
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Start Time: Wed, 12/30/2015 @ 01:08:31
End Time: Wed, 12/30/2015 @ 01:09:36
OverallResult: FAIL
ExitCode: (0x10090009:SF_GENESIS_CDU_ERROR)
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Environment Settings:
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Input Parameters:
argv[1]: -PROCESS_SSD
argv[2]: 0:0:0:0
argv[3]: /home/Shayne/kk/mpt/FW_SF-2000_B01_MP1-refresh_3-1-9--123456/FW_SF-2000_B01_MP1-refresh_3-1-9.123456.mfp
argv[4]: /home/Shayne/kk/mpt/FW_SF-2000_B01_MP1-refresh_3-1-9--123456/Configuration_Files/22214.123456.12.driveconfig
argv[5]: 12345
argv[6]: www_123
argv[7]: log=/home/Shayne/kk/2281.log
Log File: SF_Genesis_Main_Log__Wed_12.30.2015_01.08.31.log
Hostname: MicroAMD
Host IP Address: 192.168.1.9
Port Number: 0
DeviceName: /dev/sg0
SF_Genesis Version: v1.7.0.01020130612-fc14-32bit
SF_Core Library Version: v1.7.1.20130612-fc14-32bit
SF_OS_Information: Linux 2.6.35.6-45.fc14.i686 #1 SMP Mon Oct 18 23:56:17 UTC 2010 i686
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Post Processing Device Information:
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
WWN OUI: UNKNOWN
WWN UniqueID: UNKNOWN
Serial No.: UNKNOWN
Model No.: UNKNOWN
Firmware Revision: UNKNOWN
ROM Revision: UNKNOWN
NAND Page Size: UNKNOWN
Number Of Chip Enable: UNKNOWN
Logical Sectors: UNKNOWN
NAND ID: UNKNOWN
Flash Manufacturer: UNKNOWN
Flash Device: UNKNOWN
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
SandForce Genesis Utility v1.7.0.01020130612-fc14-32bit
SF_Core Library: v1.7.1.20130612-fc14-32bit
Copyright 2010-2012, LSI Corporation, All Rights Reserved Worldwide.
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
[Wed 12/30/2015 01:08:31] - SF_Genesis has been invoked with the following parameters:
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
argv[1]: -PROCESS_SSD
argv[2]: 0:0:0:0
argv[3]: /home/Shayne/kk/mpt/FW_SF-2000_B01_MP1-refresh_3-1-9--123456/FW_SF-2000_B01_MP1-refresh_3-1-9.123456.mfp
argv[4]: /home/Shayne/kk/mpt/FW_SF-2000_B01_MP1-refresh_3-1-9--123456/Configuration_Files/22214.123456.12.driveconfig
argv[5]: 12345
argv[6]: www_123
argv[7]: log=/home/Shayne/kk/2281.log
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
[Wed 12/30/2015 01:08:31] - Instructing the operating system to purge any existing cached data for device: '0:0:0:0'
[Wed 12/30/2015 01:08:36] - Issuing a discovery command for device: '0:0:0:0'
[Wed 12/30/2015 01:08:41] - Discovery command completed...
[Wed 12/30/2015 01:08:41] - Waiting 5 seconds for the system to settle...
[Wed 12/30/2015 01:08:46] - Device designation string '0:0:0:0' is mapped to node '/dev/sg0'
[Wed 12/30/2015 01:08:46] - Proceeding to process SSD device with the following parameters:
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
DeviceName = /dev/sg0
MFP Package Filename = /home/Shayne/kk/mpt/FW_SF-2000_B01_MP1-refresh_3-1-9--123456/FW_SF-2000_B01_MP1-refresh_3-1-9.123456.mfp
Configuration File = /home/Shayne/kk/mpt/FW_SF-2000_B01_MP1-refresh_3-1-9--123456/Configuration_Files/22214.123456.12.driveconfig
Serial No. = 12345
World Wide Name = www_123
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
[Wed 12/30/2015 01:08:46] - Successfully received the IDENTIFY data from the drive...
[Wed 12/30/2015 01:08:46] - Validating Manufacturing Firmware Package: /home/Shayne/kk/mpt/FW_SF-2000_B01_MP1-refresh_3-1-9--123456/FW_SF-2000_B01_MP1-refresh_3-1-9.123456.mfp
[Wed 12/30/2015 01:08:54] - Successfully opened the package: /home/Shayne/kk/mpt/FW_SF-2000_B01_MP1-refresh_3-1-9--123456/FW_SF-2000_B01_MP1-refresh_3-1-9.123456.mfp
[Wed 12/30/2015 01:08:54] - file /home/Shayne/kk/mpt/FW_SF-2000_B01_MP1-refresh_3-1-9--123456/Configuration_Files/22214.123456.12.driveconfig Loaded successfully
[Wed 12/30/2015 01:08:54] - Warning: Unable to query diagnostics information to perform power management settings check
[Wed 12/30/2015 01:08:54] - B01 Power Management configuration request detected
[Wed 12/30/2015 01:08:54] - Successfully extracted *.DriveConfig file: /home/Shayne/kk/mpt/FW_SF-2000_B01_MP1-refresh_3-1-9--123456/Configuration_Files/22214.123456.12.driveconfig
[Wed 12/30/2015 01:08:54] - Extracted Config_ID: 1 (22214) in DriveConfig file: /home/Shayne/kk/mpt/FW_SF-2000_B01_MP1-refresh_3-1-9--123456/Configuration_Files/22214.123456.12.driveconfig
[Wed 12/30/2015 01:08:54] - Extracted SerialOutputControl: 0
[Wed 12/30/2015 01:08:54] - Searching for flashware image for configuration 22214
[Wed 12/30/2015 01:08:54] - Manifest found for configuration 22214
[Wed 12/30/2015 01:08:54] - Flashware image extracted: 22214_fw_cl_mlc_Micron_64Gb_MT29F64G08CBAAAWP_2Q_1C_1D_PP_R00751_s512.vic
[Wed 12/30/2015 01:08:54] - Searching for manufacturing image for configuration 22214
[Wed 12/30/2015 01:08:54] - Manifest found for configuration 22214
[Wed 12/30/2015 01:08:54] - Manufacturing image extracted: 22214_mf_mlc_Micron_64Gb_MT29F64G08CBAAAWP_2Q_1C_1D_PP_R00751_s512.vic
[Wed 12/30/2015 01:08:54] - Proceeding in ROM mode, download feature 3...
[Wed 12/30/2015 01:08:54] - Successfully downloaded MFB to the drive...
[Wed 12/30/2015 01:08:54] - Waiting (5 sec) for the drive to settle...
[Wed 12/30/2015 01:08:59] - Successfully received the IDENTIFY data from the drive...
[Wed 12/30/2015 01:08:59] - Firmware revision reported to be: '319ABBM0'. This indicates MFB download was successful.
[Wed 12/30/2015 01:08:59] - Successfully enabled SMART capabilities...
[Wed 12/30/2015 01:09:02] - Successfully issued a diagnostic unlock...
[Wed 12/30/2015 01:09:03] - Performing the flash test of block 0 (0x0000)...
[Wed 12/30/2015 01:09:04] - Flash Test Results:
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
-----------------------------------------------------------------------------
Flash Test Parameters:
-----------------------------------------------------------------------------
Block Count: 0
Page Count: 1
Bus Count: 2
Chip Enabled Count: 1
Die Count: 1
Lane Count: 4
Plane Count: 2
-----------------------------------------------------------------------------
Results Notes:
-----------------------
N1 - At least one page tested and passed with no bit errors.
N2 - No test data available. Test may have aborted, or failed during the testing.
N3 - At least one page tested and had errors less than or equal to half the range of ECC correction power.
N4 - At least one erased page tested had bit error rate greater than half the correction power.
N5 - Walking zeros test failed.
N6 - Walking ones test failed.
N7 - Block contained factory bad block markings and testing was skipped.
N8 - At least one page tested and had bit error rate greater than the correction power on plane 0.
N9 - Block in plane 0 was marked as a factory bad block.
N10 - At least one page tested and had bit error rate greater than the correction power on plane 1.
N11 - Block in plane 1 was marked as a factory bad block.
-----------------------------------------------------------------------------
+------+------+------+------+--------+--------------------------------------------+---------+
| Bus | CE | Die | Lane | Value | Result Notes | Overall |
+------+------+------+------+--------+--------------------------------------------+---------+
| 0 | 0 | 0 | 0 | 0x0002 | N3 | WARNING |
+------+------+------+------+--------+--------------------------------------------+---------+
| 0 | 0 | 0 | 1 | 0x0003 | N1,N3 | WARNING |
+------+------+------+------+--------+--------------------------------------------+---------+
| 0 | 0 | 0 | 2 | 0x0001 | N1 | PASS |
+------+------+------+------+--------+--------------------------------------------+---------+
| 0 | 0 | 0 | 3 | 0x0003 | N1,N3 | WARNING |
+------+------+------+------+--------+--------------------------------------------+---------+
| 1 | 0 | 0 | 0 | 0x0003 | N1,N3 | WARNING |
+------+------+------+------+--------+--------------------------------------------+---------+
| 1 | 0 | 0 | 1 | 0x0003 | N1,N3 | WARNING |
+------+------+------+------+--------+--------------------------------------------+---------+
| 1 | 0 | 0 | 2 | 0x0001 | N1 | PASS |
+------+------+------+------+--------+--------------------------------------------+---------+
| 1 | 0 | 0 | 3 | 0x0003 | N1,N3 | WARNING |
+------+------+------+------+--------+--------------------------------------------+---------+
-----------------------------------------------------------------------------
Total Number of test results: 8
Number of failures: 0
Number of Passed with warnings: 6
No. Passed without warnings: 2
-----------------------------------------------------------------------------
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
[Wed 12/30/2015 01:09:04] - Performing the FORMAT Command with the following parameters:
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
MemoryWearCycleCapability = 0
CurrentPE_CycleCount = 0
LifeInSeconds = 0
LogicalCapacity = 125045424
SectorSize = 512
SectorAlignmentOffset = 0
ExpectedMemoryID = 34860 (0x882C)
ExpectedNumDies = 0
SerialOutputControl = 0
Time[8] = 0x0000000000000000
MiscFlag_Erase_R_Block = 0
MiscFlag_PanicHandlingEnabled = 0
MiscFlag_PanicOnSATA_Error = 0
MiscFlag_WriteThrottlingTestMode = 0
MiscFlag_DisableUserBandECCX = 1
L_PageSize = 0
E_PageSize = 0
ErrorCorrectionPower = 0
ConfigDeviceReadDisturbCount = 0
ConfigDeviceReadDisturbCountLow = 0
ExtraOptions_0_1 = 0
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
[Wed 12/30/2015 01:09:23] - FORMAT command completed...
[Wed 12/30/2015 01:09:23] - Waiting (2 sec) for the drive to settle...
[Wed 12/30/2015 01:09:25] - Setting up the stamp information through CDU command...
[Wed 12/30/2015 01:09:36] - FATAL_ERROR: Could not perform the ReadDriveConfigUnique() operation on the drive... (0x11000001:SF_SG_DEVICE_CHECK_CONDITION_ERROR)
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Extended Error data:
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
ATA COMMAND : 0x00B0 (176)
ATA FEATURE : 0x00D5 (213)
Device Status: 0x0001 (1)
Driver Status: 0x0000 (0)
Host Status: 0x0008 (8)
~~~~~~~~~~~~~~
Sense Data:
~~~~~~~~~~~~~~
0 - No Sense: 114 (0x72) OK
1 - Recovered Error: 11 (0x0B) FAIL
2 - Not Ready: 0 (0x00) OK
3 - Medium Error: 0 (0x00) OK
4 - Hardware Error: 0 (0x00) OK
5 - Illegal Request: 0 (0x00) OK
6 - Unit Attention: 0 (0x00) OK
7 - Data Protect: 14 (0x0E) OK
8 - Blank Check: 9 (0x09) OK
9 - Vendor Specific: 12 (0x0C) OK
10 - Copy Aborted: 0 (0x00) OK
11 - Aborted Command: 0 (0x00) OK
12 - Equal Comparison: 0 (0x00) NA
13 - Volume Overflow: 7 (0x07) NA
14 - Miscompare: 0 (0x00) OK
15 - Reserved: 225 (0xE1) NA
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
System Trace:
~~~~~~~~~~~~~~~~
[ 86.400815] sd 0:0:0:0: [sda] 64 512-byte logical blocks: (32.7 kB/32.0 KiB)
[ 86.400822] sd 0:0:0:0: [sda] 4096-byte physical blocks
[ 86.400949] sd 0:0:0:0: [sda] Write Protect is off
[ 86.400955] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 86.401011] sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 86.402517] sda:
[ 86.402811] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 86.414292] unknown partition table
[ 86.416581] sd 0:0:0:0: [sda] Attached SCSI disk
[ 136.328613] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 136.328622] ata1.00: ST-ATA: DRQ=0 without device error, dev_stat 0x50
[ 136.328630] ata1.00: failed command: SMART
[ 136.328642] ata1.00: cmd b0/d5:07:e1:4f:c2/00:00:00:00:00/00 tag 0 pio 3584 in
[ 136.328645] res 50/00:07:e1:4f:c2/00:00:00:00:00/00 Emask 0x202 (HSM violation)
[ 136.328652] ata1.00: status: { DRDY }
[ 136.328672] ata1: soft resetting link
[ 136.498252] ata1.00: model number mismatch 'SandForce{200026BB}' != 'SandForce'
[ 136.498287] ata1.00: revalidation failed (errno=-19)
[ 141.479091] ata1: soft resetting link
[ 141.649283] ata1.00: model number mismatch 'SandForce{200026BB}' != 'SandForce'
[ 141.649291] ata1.00: revalidation failed (errno=-19)
[ 141.649298] ata1.00: disabled
[ 146.630072] ata1: soft resetting link
[ 146.800442] ata1.00: failed to read native max address (err_mask=0x1)
[ 146.800448] ata1.00: HPA support seems broken, skipping HPA handling
[ 146.800458] ata1.00: ATA-9: SandForce, 319ABBM0, max UDMA/133
[ 146.800465] ata1.00: 125000000 sectors, multi 16: LBA48 NCQ (depth 0/32)
[ 146.819345] ata1.00: configured for UDMA/133
[ 146.819374] ata1: EH complete
[ 146.819395] ata1.00: detaching (SCSI 0:0:0:0)
[ 146.823412] sd 0:0:0:0: [sda] Stopping disk
[ 146.823781] scsi 0:0:0:0: Direct-Access ATA SandForce 319A PQ: 0 ANSI: 5
[ 146.824189] sd 0:0:0:0: Attached scsi generic sg2 type 0
[ 146.840068] sd 0:0:0:0: [sda] 125000000 512-byte logical blocks: (64.0 GB/59.6 GiB)
[ 146.840147] sd 0:0:0:0: [sda] Write Protect is off
[ 146.840151] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 146.840184] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 146.840626] sda:
[ 146.840780] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 146.840785] ata1.00: BMDMA stat 0x25
[ 146.840789] ata1.00: failed command: READ DMA
[ 146.840797] ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 146.840798] res 51/04:08:00:00:00/00:00:00:00:00/e0 Emask 0x1 (device error)
[ 146.840802] ata1.00: status: { DRDY ERR }
[ 146.840805] ata1.00: error: { ABRT }
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
[Wed 12/30/2015 01:09:36] - End of Genesis manufacturing log.
[Wed 12/30/2015 01:09:36] - Exiting...
还望各位大神不吝赐教，谢谢了
[ 此帖被microamd在2015-12-30 14:45重新编辑 ]
