之前无意得到16G的金胜SSD装个WIN7x64就爆红了，
后来看到坛友出2281的拆机板，就入了一个，苦逼攒不够F，关键是等不急想自己折腾个固态体验一把
刷了一个礼拜交易区那天发现有人出平板拆机F，想下价格实惠就入了8片，老板送1片
到货后立马焊F，因卖家说用安国清空过，所以一次性全贴上，
因在公司做测试对于这点芯片还是很自信，全贴再用酒精清洗
微距神器，x10倍PEAK 目镜
中间开卡在AMD台式机上FC14一直问题不断，
后来问了下坛里大神才知道FC在AMD平台会出现莫名其妙的一堆问题，
然后果断换到自己的i5的4740G本本上，安装完各种工具后点下开始出现进度条，满心期待的等......
进度跑到85%左右冒红出现崩溃英文，顿时心都凉半截，果断打开LOG查找原因，
后来和PDF里对比也没找到问题，就拷出LOG关机准备发帖求助坛友：现贴上望大神帮忙解答
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
SandForce Genesis Utility v1.5.21.20110919-fc14-32bit
SF_Core Library: v1.7.0.20110919-fc14-32bit
Copyright 2010-2011, SandForce Inc., All Rights Reserved Worldwide.
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
[Tue 07/01/2014 03:19:08] - SF_Genesis has been invoked with the following parameters:
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
argv[1]: -PROCESS_SSD
argv[2]: 1:0:0:0
argv[3]: /root/ssd/mpt/FW_SF-2000_MP_3-3-0_Client--123456/FW_SF-2000_MP_3-3-0_Client.123456.mfp
argv[4]: /root/ssd/mpt/FW_SF-2000_MP_3-3-0_Client--123456/Configuration_Files/SandForce/22214.123456.driveconfig
argv[5]: 123321
argv[6]: 456789
argv[7]: LOG=/root/ssd/mpt/123321_wu_DATETIMESTAMP_1.0.0.0_PROCESS_SSD_RESULT.log
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
[Tue 07/01/2014 03:19:08] - Instructing the operating system to purge any existing cached data for device: '1:0:0:0'
[Tue 07/01/2014 03:19:13] - Issuing a discovery command for device: '1:0:0:0'
[Tue 07/01/2014 03:19:18] - Discovery command completed...
[Tue 07/01/2014 03:19:18] - Waiting 5 seconds for the system to settle...
[Tue 07/01/2014 03:19:23] - Device designation string '1:0:0:0' is mapped to node '/dev/sg1'
[Tue 07/01/2014 03:19:23] - Proceeding to process SSD device with the following parameters:
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
DeviceName = /dev/sg1
MFP Package Filename = /root/ssd/mpt/FW_SF-2000_MP_3-3-0_Client--123456/FW_SF-2000_MP_3-3-0_Client.123456.mfp
Configuration File = /root/ssd/mpt/FW_SF-2000_MP_3-3-0_Client--123456/Configuration_Files/SandForce/22214.123456.driveconfig
Serial No. = 123321
World Wide Name = 456789
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
[Tue 07/01/2014 03:19:23] - Successfully received the IDENTIFY data from the drive...
[Tue 07/01/2014 03:19:24] - Successfully opened the package: /root/ssd/mpt/FW_SF-2000_MP_3-3-0_Client--123456/FW_SF-2000_MP_3-3-0_Client.123456.mfp
[Tue 07/01/2014 03:19:24] - Successfully extracted *.DriveConfig file: /root/ssd/mpt/FW_SF-2000_MP_3-3-0_Client--123456/Configuration_Files/SandForce/22214.123456.driveconfig
[Tue 07/01/2014 03:19:24] - Extracted Config_ID: 1 (22214) in DriveConfig file: /root/ssd/mpt/FW_SF-2000_MP_3-3-0_Client--123456/Configuration_Files/SandForce/22214.123456.driveconfig
[Tue 07/01/2014 03:19:24] - Extracted SerialOutputControl: 0
[Tue 07/01/2014 03:19:24] - Successfully extracted Config record: 22214
[Tue 07/01/2014 03:19:24] - Successfully extracted flashware image: 22214_fw_cl_mlc_Micron_64Gb_MT29F64G08CBAAAWP_2Q_1C_1D_PP_R00751_s512.vic
[Tue 07/01/2014 03:19:24] - Successfully extracted manufacturing image: 22214_mf_mlc_Micron_64Gb_MT29F64G08CBAAAWP_2Q_1C_1D_PP_R00751_s512.vic
[Tue 07/01/2014 03:19:24] - Proceeding in non-ROM mode, Download feature 7...
[Tue 07/01/2014 03:19:25] - Successfully downloaded MFB to the drive...
[Tue 07/01/2014 03:19:25] - Waiting (5 sec) for the drive to settle...
[Tue 07/01/2014 03:19:30] - Successfully received the IDENTIFY data from the drive...
[Tue 07/01/2014 03:19:30] - Firmware revision reported to be: '330ABBM0'. This indicates MFB download was successful.
[Tue 07/01/2014 03:19:30] - Successfully enabled SMART capabilities...
[Tue 07/01/2014 03:19:31] - Successfully issued a diagnostic unlock...
[Tue 07/01/2014 03:19:31] - Performing the flash test of block 0 (0x0000)...
[Tue 07/01/2014 03:19:33] - Flash Test Results:
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
-----------------------------------------------------------------------------
Flash Test Parameters:
-----------------------------------------------------------------------------
Block Count: 0
Page Count: 1
Bus Count: 2
Chip Enabled Count: 1
Die Count: 1
Lane Count: 4
Plane Count: 2
-----------------------------------------------------------------------------
Results Notes:
-----------------------
N1 - At least one page tested and passed with no bit errors.
N2 - No test data available. Test may have aborted, or failed during the testing.
N3 - At least one page tested and had errors less than or equal to half the range of ECC correction power.
N4 - At least one erased page tested had bit error rate greater than half the correction power.
N5 - Walking zeros test failed.
N6 - Walking ones test failed.
N7 - Block contained factory bad block markings and testing was skipped.
N8 - At least one page tested and had bit error rate greater than the correction power on plane 0.
N9 - Block in plane 0 was marked as a factory bad block.
N10 - At least one page tested and had bit error rate greater than the correction power on plane 1.
N11 - Block in plane 1 was marked as a factory bad block.
-----------------------------------------------------------------------------
+------+------+------+------+--------+--------------------------------------------+---------+
| Bus | CE | Die | Lane | Value | Result Notes | Overall |
+------+------+------+------+--------+--------------------------------------------+---------+
| 0 | 0 | 0 | 0 | 0x0003 | N1,N3 | WARNING |
+------+------+------+------+--------+--------------------------------------------+---------+
| 0 | 0 | 0 | 1 | 0x0002 | N3 | WARNING |
+------+------+------+------+--------+--------------------------------------------+---------+
| 0 | 0 | 0 | 2 | 0x0002 | N3 | WARNING |
+------+------+------+------+--------+--------------------------------------------+---------+
| 0 | 0 | 0 | 3 | 0x0003 | N1,N3 | WARNING |
+------+------+------+------+--------+--------------------------------------------+---------+
| 1 | 0 | 0 | 0 | 0x0002 | N3 | WARNING |
+------+------+------+------+--------+--------------------------------------------+---------+
| 1 | 0 | 0 | 1 | 0x0002 | N3 | WARNING |
+------+------+------+------+--------+--------------------------------------------+---------+
| 1 | 0 | 0 | 2 | 0x0002 | N3 | WARNING |
+------+------+------+------+--------+--------------------------------------------+---------+
| 1 | 0 | 0 | 3 | 0x0002 | N3 | WARNING |
+------+------+------+------+--------+--------------------------------------------+---------+
-----------------------------------------------------------------------------
Total Number of test results: 8
Number of failures: 0
Number of Passed with warnings: 8
No. Passed without warnings: 0
-----------------------------------------------------------------------------
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
[Tue 07/01/2014 03:19:34] - Performing the FORMAT Command with the following parameters:
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
MemoryWearCycleCapability = 0
CurrentPE_CycleCount = 0
LifeInSeconds = 0
LogicalCapacity = 125045424
SectorSize = 512
SectorAlignmentOffset = 0
ExpectedMemoryID = 34860 (0x882C)
ExpectedNumDies = 0
SerialOutputControl = 0
Time[8] = 0x0000000000000000
MiscFlag_Erase_R_Block = 0
MiscFlag_PanicHandlingEnabled = 0
MiscFlag_PanicOnSATA_Error = 0
MiscFlag_WriteThrottlingTestMode = 0
MiscFlag_DisableUserBandECCX = 1
L_PageSize = 0
E_PageSize = 0
ErrorCorrectionPower = 0
ConfigDeviceReadDisturbCount = 0
ConfigDeviceReadDisturbCountLow = 0
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
[Tue 07/01/2014 03:19:52] - FORMAT command completed...
[Tue 07/01/2014 03:19:52] - Waiting (2 sec) for the drive to settle...
[Tue 07/01/2014 03:19:54] - Setting up the stamp information through CDU command...
[Tue 07/01/2014 03:19:57] - Waiting (2 sec) for the drive to settle...
[Tue 07/01/2014 03:19:59] - Downloading the flashware to the drive...
[Tue 07/01/2014 03:20:00] - Successfully downloaded flashware to the drive...
[Tue 07/01/2014 03:20:00] - Waiting (15 sec) for the drive to settle...
[Tue 07/01/2014 03:20:15] - Successfully received the IDENTIFY data from the drive...
[Tue 07/01/2014 03:20:15] - Firmware revision reported to be: 'NC '
[Tue 07/01/2014 03:20:15] - Enabling SMART support...
[Tue 07/01/2014 03:20:15] - Issuing a diagnostic unlock to the drive...
[Tue 07/01/2014 03:20:16] - Setting up Max LBA settings...
[Tue 07/01/2014 03:20:20] - Applying the remaining ConfigUniqueDrive settings...
[Tue 07/01/2014 03:20:22] - Setting 'Configuration ID' to '22214'
[Tue 07/01/2014 03:20:22] - Setting 'Customer ID' to '123456'
[Tue 07/01/2014 03:20:22] - Setting 'Model No.' to 'Sandforce_sf2281_64g'
结果关机进入 window7后直接提示安装驱动弹出发现磁盘，
需要从新引导扇区点确定然后格式化出现盘符？？？
惊喜啊，这样也行？然后测试后截图
SATA2下AS
换到AMD台式机SATA3上的AS，和三棒840EVO对比
虽然跑分低，但是4K机械没得比，附上ATTO图
最后来一个DiskInfo截图，健康为0，SSD寿命为0，大神看下什么问题？
