话说，入坛子已有大半年时间，向前辈学习硬改了几个路由，刷op dd tt 等等，刮U 加USB，op挂载数学头疼，硬改基本能做了。
在网友的分享下入手了全新路由：19.9 fir300M,29.9 FIR303C,35 的金亚306r(5357芯片）;双12又看到了33元的仕牌SP-WR300整了一个今天到货。
首先还是拆开看看，不看不知道，原来我还是初入论坛的小小白：烦请大神指点-----------内存则么看？？？？？
因下班前到的，单位拆开照了几张片片先上，后续补充》
另向我咨询购买地址的坛友，如果买了，再次表示歉意----分享的产品不够好！
网站上参数说明：
芯片见参数说明一致，闪存为25Q16 2M，，内存哪里去了？利用主芯片的内存了？
背面也没啥原件，没内存。
硬改看来没戏了？ --------------- 正好缺2个网络变压器可拆。
开机一刻钟： 无线连接进入web，点几次约三分钟吧，页面死，要重新连接无线，环境温度20度，主芯片约35度，无线芯片手放不住温度应该高于40度。
20141216更新：有线连接上级路由，无线AP，电脑无线连接测速：
20141217更新TTL信息，大神看看此路由是否使用内存？ 内存借用哪里？
Booting...
@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@
@
@ chip__no chip__id mfr___id dev___id cap___id size_sft dev_size chipSize
@ 0000000h 0c84015h 00000c8h 0000040h 0000015h 0000000h 0000015h 0200000h
@ blk_size blk__cnt sec_size sec__cnt pageSize page_cnt chip_clk chipName
@ 0010000h 0000020h 0001000h 0000200h 0000100h 0000010h 000004eh GD25Q16
@
@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@
---RealTek(RTL8196E)at 2014.09.03-14:47+0800 v1.5 [16bit](400MHz)
check_image_header return_addr:05010000 bank_offset:00000000
no sys signature at 00010000!
no sys signature at 00020000!
no sys signature at 00030000!
no sys signature at 00011000!
no sys signature at 00012000!
no sys signature at 00013000!
no sys signature at 00014000!
no sys signature at 00015000!
no sys signature at 00016000!
no sys signature at 00017000!
no sys signature at 00018000!
no sys signature at 00019000!
no sys signature at 0001A000!
no sys signature at 0001B000!
no sys signature at 0001C000!
no sys signature at 0001D000!
no sys signature at 0001E000!
no sys signature at 0001F000!
no sys signature at 00021000!
no sys signature at 00022000!
no sys signature at 00023000!
no sys signature at 00024000!
no sys signature at 00025000!
no sys signature at 00026000!
no sys signature at 00027000!
no sys signature at 00028000!
no sys signature at 00029000!
no sys signature at 0002A000!
no sys signature at 0002B000!
no sys signature at 0002C000!
no sys signature at 0002D000!
no sys signature at 0002E000!
no sys signature at 0002F000!
no sys signature at 00031000!
no sys signature at 00032000!
no sys signature at 00033000!
no sys signature at 00034000!
no sys signature at 00035000!
no sys signature at 00036000!
no sys signature at 00037000!
no sys signature at 00038000!
no sys signature at 00039000!
no sys signature at 0003A000!
no sys signature at 0003B000!
no sys signature at 0003C000!
no sys signature at 0003D000!
no sys signature at 0003E000!
no sys signature at 0003F000!
no sys signature at 00040000!
no sys signature at 00041000!
no sys signature at 00042000!
no sys signature at 00043000!
no sys signature at 00044000!
no sys signature at 00045000!
no sys signature at 00046000!
no sys signature at 00047000!
no sys signature at 00048000!
no sys signature at 00049000!
no sys signature at 0004A000!
no sys signature at 0004B000!
no sys signature at 0004C000!
no sys signature at 0004D000!
no sys signature at 0004E000!
no sys signature at 0004F000!
Jump to image start=0x80500000...
decompressing kernel:
Uncompressing... done, booting the kernel.
done decompressing kernel.
start address: 0x800004c4
0xc84015 GD25Q16
[cyg_net_init] Init: mbinit(0x00000000)
[cyg_net_init] Init: cyg_net_init_devs(0x00000000)
Init device 'rltk819x_eth0'
Init device 'rltk819x_eth1'
Init device 'rltk819x_eth2'
Init device 'rltk819x_eth3'
Init device 'rltk819x_eth4'
[peth0] added, mapping to [eth1]...
Init device 'rltk819x_peth0'
Init device 'rltk819x_eth7'
Init device 'rltk819x_wlan0'
[pwlan0] added...
Init device 'rltk819x_pwlan0'
Init device 'rltk819x_wlan0-wds0'
Init device 'rltk819x_wlan0-wds1'
Init device 'rltk819x_wlan0-wds2'
Init device 'rltk819x_wlan0-wds3'
Init device 'rltk819x_wlan0-va0'
Init device 'rltk819x_wlan0-vxd'
[cyg_net_init] Init: loopattach(0x00000000)
[cyg_net_init] Init: cyg_ppp_pppattach(0x00000000)
[cyg_net_init] Init: ifinit(0x00000000)
[cyg_net_init] Init: domaininit(0x00000000)
[cyg_net_init] Init: cyg_net_add_domain(0x801f8dec)
New domain internet at 0x00000000
IP packet filtering initialized, divert enabled, rule-based forwarding enabled, default to deny, logging disabled
Realtek FastPath:v1.03
[cyg_net_init] Init: cyg_net_add_domain(0x801f8acc)
New domain route at 0x00000000
[cyg_net_init] Init: call_route_init(0x00000000)
[cyg_net_init] Init: sysctl_register_all(0x00000000)
[cyg_net_init] Done
Creating Init Thread...
Realtek GPIO init
************* Initialize MAC/PHY parameter *************
[MAC_REG_8192Emp]
[PHY_REG_8192Emp]
[PHY_REG_PG_8192E_new]
[AGC_TAB_8192Emp]
RadioA_8192Emp
[RadioB_8192Emp]
[REG_TXPWR_TRK_8192E]
eth0: promiscuous mode enabled
wlan0: promiscuous mode enabled
bridge0: flags=8842<BROADCAST,RUNNING,SIMPLEX,MULTICAST>
Interfaces:
wlan0 flags=3<LEARNING,DISCOVER>
eth0 flags=3<LEARNING,DISCOVER>
Addresses (max cache: 100, timeout: 300):
Creating httpd Thread...
enter dhcpd_startup
Starting DHCPD thread
config_wan,2641, start config wan
pppoe_init 1437 #######
pppoe_init 1441 #######
config_wan,2661, start config wan
Ineintt eWrA Nd hIcnptce_rsftaacret.u.p.
Starting WAN DHCPC thread
rtl_setDoubleAliasIp 528 aliasAddress2.s_addr=0x0
start dst loop...
cyg_dns_proxy_daemon-->734,DNSPROXY Start......
brute_force_attack_mitigation ThresHold[10]
WiFi Simple Config v2.14-wps2.0 (2014.11.21-00:58+0000).
IEEE 802.11f (IAPP) using interface eth0 (v196e_13_D141121-SeaPai)
#
