昨天新买的16G 我拆了主控芯片背面的那片FLASH另作他用，但剩下的这片量产就出错！（不是量产作为启动盘）试了几个工具都不行 求大神指点！有M币奖励！ 先报Error8 我加了ID17=1 又报 错误25
一 card info 检测结果---------------- Device 1------------------ CE-1, Flash ID=2C-88-04-4B-A9-00-00 ### Error: No found boot block (non-MPed disk) 二 没加ID=17 Report 内容 Device 1:0xB5 MP Version:2.182
INI_File_Name:6692_IM25_256P_8KB.INI Random delay 0 msec
--- Download MP ISP --- Auto CE: 0xFF 0x01 0xFF 0xFF 0xFF 0xFF 0xFF 0xFF
CE-1, Flash ID=2C-88-04-4B-A9-00-00-00 Page/Block=256
Searching SORTING BOARD table ... --> Not Found
---> Max BAD/DIE = 0 Total good blocks after SCAN: 4096 / 4096, Bad block=0
==> 2-Plane mode Max. Bad Block Allowed = 174(0)
Adjust Max LBA = 15646720, 15646656 MaxWindows=2/1910, MaxLBA=15646656, Size=7639 MB
Max BAD of one plane is 0 (43),4096,1,1 RootSector=0xF4B,Sec/Cluster=64, SuperPage=64 ---> Alignment=53
Boot Block=0x0002,0x0004 Lun0(15646656), Lun1(0), Public=15646656, Secure=0, CDROM=0
Special FE Config = 54-0B-00 Defect Table Block=0x0008
--- Download ISP Code:C:\USERS\L\DESKTOP\新建文件夹 (2)\6692_IM25_MP_V2182\ISP_CODE\6692_B5-IM_20110214_VB70200_8277.BIN--- --- ISP Code installed.
Lun0(15646656), Lun1(0), Public=15646656, Secure=0, CDROM=0 Public,Secure,CDROM = 15646656,0,0
PHY: E2/E4/E6=72h/36h/04h, D0/C0/CFG10=DFh/0Bh/87h SN=0015AF000A60FF1072DD202E
=== Preformat Done === Low Level Format DONE
Store INI/ERROR MSG to Block-0x0002:78. ### Error: Device capacity is 0 bytes
三 加ID=17后 Device 1:0xB5
MP Version:2.182
INI_File_Name:6692_IM25_256P_8KB.INI
Random delay 0 msec
--- Download MP ISP ---
Auto CE: 0xFF 0x01 0xFF 0xFF 0xFF 0xFF 0xFF 0xFF
CE-1, Flash ID=2C-88-04-4B-A9-00-00-00
Page/Block=256
Searching SORTING BOARD table ...
--> Not Found
---> Max BAD/DIE = 0
Total good blocks after SCAN: 4096 / 4096, Bad block=0
==> 2-Plane mode
MaxWindows=2/-60, MaxLBA=16359424, Size=7988 MB
Max BAD of one plane is 0 (1028),4096,1,1
RootSector=0xFF9,Sec/Cluster=64, SuperPage=64 ---> Alignment=7
Boot Block=0x0002,0x0004
Lun0(16359424), Lun1(0), Public=16359424, Secure=0, CDROM=0
Special FE Config = 54-0B-00
Defect Table Block=0x0008
### Err: Preformat Abort ###
not enought block for d-block + min_algorithm_need
### Error: Low level format failed ###
Store INI/ERROR MSG to Block-0x0002:78.
---> Max BAD/DIE = 0
四 INI内容
[OEM]
PN=6692 + Intel & Micron 25nm Normal Flash (256P,8KB)
Note=6692_B5-IM_20110214_VB70200_8277.BIN
VID=0
PID=0
VENDOR_NAME="3SYSTEM"
PRODUCT_NAME="USB Flash Disk"
STRING_DESC_ENABLE=1
SN_CustomerCode=0x0F
[FEATURE_SETTING]
FLASH_OP="ALL123"
ID35=1
ID17=1
[CDROM]
CDROM_ISO=D:\WinPE.iso
[ISP]
Code=6692_B5-IM_20110214_VB70200_8277.BIN
[LED]
LED_Period=1
LED_DutyCycle=10
[ 此帖被98078在2015-01-07 20:45重新编辑 ]
